Agilite K19 Plate Carrier 3.0

The Agilite K19 Plate Carrier 3.0 is a modular plate carrier built around fast adjustment, quick-release capability, and support for common armor and load-carriage configurations. It combines Agilite's Fast-Adjust cummerbund with the Egress quick-release system, allowing the wearer to fine-tune fit without removing the carrier.

The K19 3.0 uses a one-size-fits-all cummerbund and one-size-fits-most plate bags designed for common Small, Medium, and Large SAPI/ESAPI plates as well as 10x12-inch plates within the carrier's dimensional limits. The front plate bag is placard-compatible while retaining MOLLE underneath, allowing the carrier to be configured with either hook-backed placards or conventional MOLLE pouches.

Version 3.0 also uses removable left and right quick-release buckles. Included minimalist slide buckles can be installed when a lower-profile shoulder interface is preferred.

Key Features

• Egress quick-release system
• Fast-Adjust one-size-fits-all cummerbund can be adjusted by the wearer
• One-size-fits-most plate bags for common Small, Medium, and Large SAPI/ESAPI plates
• Compatible with standard 10x12-inch plates within specified dimensional limits
• Placard-compatible front with upper attachment points and laser-cut loop overlay
• MOLLE mounting surface remains available beneath the front loop panel
• Removable left and right quick-release buckles
• Includes minimalist slide buckles for a lower-profile shoulder setup
• Fusion Foam padding on the shoulder and rear plate-bag areas
• Front zippered admin pocket
• Skeletal shoulder design for routing communications and hydration lines
• Front and rear laser-cut hook-and-loop panels
• Rear drag handle
• Compatible with the Agilite AMAP III Assault Pack
• Agilite K-Series compatible

Plate Fit & Sizing

The K19 uses a one-size-fits-all cummerbund and one-size-fits-most plate bags. Agilite specifies compatibility with common Small, Medium, and Large SAPI/ESAPI plates and standard 10x12-inch plates.

Plate dimensions can vary between manufacturers, even when plates share the same nominal size. Check the actual height, width, and thickness of the armor against the K19 specifications before installation, particularly when using thicker rifle plates.

Placards, MOLLE & Loadout Configuration

The K19 3.0 front plate bag supports hook-backed placards through its loop field and upper attachment points. Traditional MOLLE remains available underneath, so the carrier can also be configured with conventional MOLLE-mounted magazine, medical, admin, and utility pouches.

The Fast-Adjust cummerbund also provides mounting space for compatible pouches along its length, giving the wearer additional flexibility when distributing equipment around the carrier.

Specifications

• Manufacturer: Agilite
• Model: K19 Plate Carrier 3.0
• Material: 1000D CORDURA Mil-Spec tactical nylon
• Hardware: Mil-Spec polymer buckles and hardware
• Quick Release: Egress system
• Cummerbund: Fast-Adjust, one-size-fits-all
• Plate Fit: Small, Medium, and Large SAPI/ESAPI plates
• 10x12 Plate Compatibility: Yes, within specified dimensional limits
• Maximum Plate Thickness: Up to 1.5 inches
• Chest Hook-and-Loop Panel: Approximately 9.8 x 3.5 in. (25 x 9 cm)
• Weight: 2.5 lb (1.1 kg), including Fast-Adjust cummerbund
• Front Attachment: Placard-compatible loop field with MOLLE underneath
• Pack Compatibility: Agilite AMAP III Assault Pack

Compatibility Note

The K19 3.0 is designed to accommodate a broad range of common plate sizes, but actual fit depends on plate dimensions and thickness. Verify the dimensions of your armor before ordering. The carrier itself does not determine whether a ballistic plate requires a separate backer; follow the armor manufacturer's requirements for the specific plate being used.

WARNING This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov. You must be 18 or older to shop or purchase on our website, and 21 or older to purchase ammunition or firearms. Check local laws before ordering. By ordering, you certify that you meet all federal, state, and local legal requirements. There are no returns or exchanges on armor, firearms, ammunition, or PPE. Ammunition ships UPS Ground to the lower 48 states.
We reserve the right to correct critical errors.