Barrett Scope Rings 34mm / Ultra High / 1.4"
- Shipped from our or manufacturers warehouse. You will be notified of any delays. Your card will not be charged until product ships.
- 1.00 LBS
Unlike traditional scope rings which require careful attention be paid to maintaining equal gap between the upper and lower ring halves, Barrett’s ZERO-GAP technology eliminates this tedious process. Simply tighten the cap on the indicated side, verify reticule alignment, tighten the remaining side, and fire away. The end result is a perfect fit between scope and mount that will withstand even the heaviest recoiling rifles. Machined from 7075-T5 aluminum and with MIL-SPEC Type III anodized finish, ZERO-GAP Rings are available in a variety of heights for both 30mm, 34mm, and 35mm optics. Simplicity at its finest.
Barrett ZERO-GAP Rings are wider than typical rings at 1.2 inches. This creates a greater surface area of contact between the ring and scope maintube. The benefit is a secure grip on the optic that will hold up under heavy recoil. Along with this solid connection comes protection for your expensive scope. The broad clamping area spreads out the forces and reduces the likelihood of denting or distorting the scope tube. The same benefits in scope holding translate directly to the mount's ability to hold on the rail. More width in rail clamping area is better.
HEAVY DUTY HARDWARE
The rail clamping cross bolt and nut are precision machined from hardened steel alloys. The cross bolt is securely pressed into the scope ring base, and the end of the bolt is staked to retain the nut. The cross bolt is designed with a broad shoulder to perfectly interface with cross slots of mil spec 1913 rail to resist even the harshest recoil. The top cap of each ring is retained by four robust Torx screws placed with broad spacing to provide consistent and evenly distributed clamping force.
PRECISION AND TOLERANCE
All critical features on Barrett ZERO-GAP Rings are machined with great care. The 30-mm bore will be exactly that with a diameter tolerance of plus or minus .001", perfect roundness and position in relation to the mounting rail. Angles and surfaces in the rail clamping feature of the lower ring are held to great positional tolerances to ensure the scope is held centered when bolted up to the rail.
FIT AND FINISH
Every component of Barrett ZERO-GAP Rings is carefully handled all the way to packaging. All edges are beautifully rounded to prevent snags and resist corner wear. The 7075 T-6 components are hard anodize coated in black to mil spec MIL-A-8625 Type III Class 2 specification for superior surface hardness (60 Rockwell) and resistance to wear. Steel components are manganese phosphate coated to mil spec DOD-P-16232 Type M Class 2 specification.
The unique scope clamping design of Barrett ZERO-GAP Rings takes care of some old optics mounting challenges. In the past, great attention was required when securing scope ring caps to maintain an equal gap between the lower ring and top cap on each side. There was also the possibility of rotating the scope out of perfect vertical reticle alignment while torquing the cap screws in a side-to-side pattern. These problems are eliminated with the ZERO-GAP design. Simply secure the cap on the indicated side until there is no gap between lower ring and cap, check for perfect reticle alignment, and then torque the remaining side to the required specification.
- Weight: 8.32oz (235.9g) (30mm), 8.45oz (239.6g) (34mm)
- Size: 30 mm, 34 mm
- Base Type: Mil-STD 1913 Rail
- Tensile Strength: 83 ksi
- Ring Width: 1.2" (3.05 cm)
- Surface Gripping Area: 8.192 inch²
- Material: 7075 T-6 Aluminum
- Finish: Hard Anodized Black
- Height (Contact Point to Scope Ring Center): 1.0"-1.7"
WARNING This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. (California law requires this warning to be given to customers in the State of California.)
Made In USA
PayPal checkout is disabled for carts that contain products with restrictions due to PayPal's acceptable use policy.
If you wish to use PayPal for part of your order please use separate shopping carts.
In an effort to be more competitive, we are moving from our free shipping policy, to a weight & destination-based shipping charge.
Until now we have been padding the sale price of our products to cover the free shipping cost. You will see overall savings when purchasing a single product but even bigger savings when purchasing multiple products at the same time. This allows us to group & ship together, eliminating excessive shipping fees. Selected marked items will still qualify for free GROUND or 2 DAY AIR shipping.
We would very like to earn your business, so you can always use the RFQ/REQUEST QUOTE for quantity orders and products protected by manufacturers MAP pricing policies.
Sales Tax Exemptions: We are required to collect sales tax on your order except for the following states: Alaska, Arizona, Delaware, Florida, Kansas, Missouri, Montana, New Hampshire, Oregon, & Puerto Rico. Other exemptions: Federal agencies, holders of state sale tax exemption/resale certificates & international sale.
Our ordering system will not charge sales tax for the above exempt states, but if you are tax exempt for any other reason check the NO SALES TAX box in the order form, sales tax will be removed prior to final billing.